How to 3D print a model bigger than your printer
You print a model that is bigger than your printer by splitting it into parts that each fit the build volume, adding joints so the parts line up, printing each part on its own plate, and assembling them. You can do the splitting by hand in a slicer or CAD program, or let CadSplit do it in one step.
1. Check what fits
Start with the build volume of your printer. A part must fit in all three directions, and it helps to leave about 5 mm of margin so the part is not printed right at the edge of the plate.
| Printer | Build volume (mm) |
|---|---|
| Bambu Lab A1 mini | 180 × 180 × 180 |
| Bambu Lab A1 | 256 × 256 × 256 |
| Bambu Lab P1S | 256 × 256 × 250 |
| Bambu Lab X1 Carbon | 256 × 256 × 250 |
| Bambu Lab H2S | 340 × 320 × 340 |
| Bambu Lab H2D | 350 × 320 × 325 |
A model only has to be too big in one direction to need a cut. A 400 mm ball on a 256 mm printer needs one cut in each direction, which makes 8 parts.
2. Decide where to cut
- Use as few cuts as you can. Every cut is a seam you have to align, glue and maybe sand.
- Cut through plain areas. Keep seams away from small details, text and thin walls.
- Think about the plate. A flat cut face makes a good first layer, so each part can lie cut face down with little or no support.
- Avoid slivers. A cut that leaves a thin strip gives you a part that warps and is hard to join.
3. Add joints
Flat faces glued together slide around while the glue sets. A joint keeps the parts in place. Common choices are pins with glue, dovetails, puzzle seams, screws and magnets. See joints for split 3D prints for when to use which.
4. Leave a gap
Printed parts come out slightly larger than drawn, so a joint needs clearance. About 0.2 mm is a normal starting point for a snug fit on a well tuned printer. Print a small test strip first if the fit matters.
5. Lay out and print
Put each part on its own plate, with the largest flat face down. Number the parts so you can tell them apart when they come off the printer.
6. Assemble in order
Interlocking seams only close one way, so the order matters. Join parts into rows or columns first, then join those groups. Dry fit before you glue.
Three ways to do the splitting
In your slicer
Bambu Studio, OrcaSlicer and PrusaSlicer have a cut tool. You place one cut plane at a time, choose connectors, and move each part to a plate yourself.
In CAD
Full control over the shape of every joint. It takes the longest, and the model has to be redone if the cut moves.
With CadSplit
Drop the model in. CadSplit picks the fewest cuts for your printer, adds the joints, lays each part on its own plate and shows the assembly order.
What it looks like in practice
These are the part counts CadSplit gives for its three example models, with dovetail seams:
| Model | A1 mini (180 mm) | A1 or P1S (256 mm) | H2D or H2S (320 mm and up) |
|---|---|---|---|
| Ball, 400 mm across | 27 parts | 8 parts | 8 parts |
| Toy car, 528 mm long | 16 parts | 6 parts | 2 parts |
| Sculpture, 542 mm long and 517 mm tall | 48 parts | 19 parts | 9 parts |
Questions
Can I print something bigger than my print bed?
Yes. Split the model into parts that each fit the build volume, add joints, print the parts and join them. The seams can be glued, screwed or left as a press fit.
How many parts will my model need?
It depends on how much bigger the model is than the printer in each direction. A 400 mm ball needs 8 parts on a 256 mm printer and 27 parts on a 180 mm printer.
Will the seams be visible?
A seam shows as a thin line. Cutting through plain areas, using a joint that aligns the parts, and a little filler or sanding makes it hard to see after painting.